![]() ![]() Putting a new belt on is merely the reverse of this process. Finally, disconnect and remove the battery so you can get the drive belt off the transaxle pulley. Then you can release the belt from the pulleys and belt guides. You will need a wrench to hold the engine crankshaft in place while removing the engine pulley bolt and washer. ![]() To remove and replace this belt, take off the flywheel screen cap. Once you have the part, disconnect your spark plug and pull the deck out from under your mower. According to Troy Bilt, this is eleven digits long and located on the left side of the Product Identification Label. You can find the right size by locating your model number. When your wheels don’t turn, try swapping your drive belt for a new MTG belt specific to your model. Troy Bilt riding mowers need an exact fit. It’s common to get the wrong size or use a generic but slightly off-width replacement. If the belt breaks, the lawn tractor won’t move.”Ī surprising amount of the time, the problem is that a mower has the wrong belt. As Sears points out, “The ground drive belt connects the engine crankshaft to the transaxle pulley to drive the rear wheels. The drive belt on your Troy Bilt Riding mower does what it sounds like. That should disengage the blades.Īlways start with the blades off. You’ll find it next to the driver’s seat on the right-hand side of the mower’s fender.ĭoing this is the only way to tell the engine to send power to those blades. Your PTO lever is what engages the blades. If this is the problem, you are in luck because the fix only takes about a minute. While this might seem odd, it’s actually a safety feature to help prevent accidents. You cannot get your Troy Bilt Riding mower to move without disengaging the blades and putting the parking brake on. Your owner’s manual will have specific details. Other models may use a slightly different system to engage the parking brake, such as pushing down the clutch. If you forget to hold down the regular brake, the parking brake will not be on the next time you climb on. If you get in the habit of following this routine, you’ll have fewer moments when your mower won’t move.įor the Troy Bilt Super Bronco, you will need to fully depress the brake pedal and hold it in while you press the parking brake button. First, turn off the blades using the PTO, then put your transmission in neutral.Īfter that, set your parking brake, turn off the engine, and remove your key. 2 – Disengaged Parking BreakĪny time you stop your Troy Bilt Riding mower, please follow the manufacturer-recommended steps. The vents in your gas cap allow air to flow into the engine, so the fuel doesn’t create a vacuum and vapor lock as you work. All you need do is quite literally unscrew it and put a new compatible cap in place. ![]() Gas caps are the easiest to remove and replace. Unfortunately, doing this risks leaving debris behind to collect, and then you’ll have the same problem over again. In some cases, you can clear a blockage manually. You’ll find a small metal clamp at each end, and once you loosen those, it is simple enough to pull the line away. Replacing clogged fuel lines is usually as simple as draining the engine, popping the line off at both ends, and putting a new one in its place. Though it is specific to the Troy-Bilt TB130, it will still give you a step-by-step visual example of the process. I recommend watching this video if you don’t know how to change your fuel filter. Long before you can’t get your mower to move, you’ll have start and stop issues where the engine dies or runs erratically.Įnsure that you check fuel and oil levels regularly and change your fuel filters as often as the manufacturer recommends for your model, usually after fifty to ninety hours of use. Gas inside your mower should always be ‘new,’ which means less than thirty days old.Ī fuel filter will usually warn you when there’s a problem. For example, old or incorrect fuel may not run the engine at all. Your fuel and air system can cause problems with your Troy Bilt Riding mower in several different ways. Luckily, I can help you troubleshoot the top five reasons why your Troy Bilt Mower won’t move so you can get your lawn back to its ordinarily pristine condition. Worse still, the idea of taking anything apart yourself to fix it can be daunting. There’s nothing worse than getting ready to go out and take care of a messy yard only to discover your mower won’t move.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |